Pasco capstone calculate momentum function

PASCO CAPSTONE CALCULATE MOMENTUM FUNCTION HOW TO
PASCO CAPSTONE CALCULATE MOMENTUM FUNCTION SOFTWARE

PASCO CAPSTONE CALCULATE MOMENTUM FUNCTION SOFTWARE

PASCO sensor equipment, computer, and DataStudio software Add-on mass.

Gyroscopic Motion - Physics Department | University of Guelph Science Workshop Collision u2013 Impulse u0026amp Momentum dg u00a9 1996, PASCO scientific P14 - 1 Experiment P14: Collision. uses a calculation on the data from one of the sensors 93 Momentum in Collisions Mechanics: momentum. Physics with the Xplorer GLX u00a9 2006 PASCO p. () momentum Qty Equipment and Materials Part Number Smart pulley and Pasco Universal Clamp Moment of Inertia Apparatus Mass and bar attachment 5 gram mass holder Read File Online - Report AbuseД¬alculation). u2022 To complete the calculation, type Momentum Cart 2 in the Calculation Name area. Science Workshop Conservation of Linear Momentum 2 dg u00a91996, PASCO scientific P17. Please note that run 8 was excluded from the calculation of average percent error for reasons described below.Experiment P17: Conservation of Linear Momentum II (Photogate) Initial and final momentum were calculated for run 1, an inelastic collision, as follows: Initial momentum (0.2123kg x 1.75 (0.2142kg x 0.372 kg x Final momentum (0.2123kg 0.2142 0.243 kg x Initial and final momentum were calculated for run 6, an elastic collision, as follows: Initial momentum (0.3143 kg x 0.97 (0.2147kg x 0.305 kg x Final momentum (0.3143 kg x (0.2147kg x 1.01 0.248 kg x Percent error values for all of the runs and a sample calculation are shown below. The initial and final momentum, as well as percent error, were calculated using Microsoft Excel. Analysis In this experiment, the distance between leading edges of the flag (change in x) was measured with a ruler, the masses were found using a digital scale, and initial velocity was measured Capstone software configured with the Pasco data acquisition system. Percent difference was then used in order to compare all of the values to one another. Once again the initial and final velocities were found in order to calculate the initial and final momentums. For the elastic collision with both masses moving, the two gliders were put at different ends of the air track and were then pushed towards the center, allowed to hit one another and bounce off. The same process is done for the elastic collision, but bumpers were attached to the front of the gliders instead of the inelastic collision pin. The initial and final velocities were found through the two photogates for each glider and were then multiplied to the mass and added together to get the initial and final momentums. The second glider was placed between the two photogates, the first glider was then pushed down the track to hit and stick to the second glider. The inelastic collision with one mass at rest was done using the inelastic collision pin and putty receptacle attached to the front of each glider.

For each type of collision (inelastic collision with one mass at rest, elastic collision with one mass at rest, and elastic with both masses moving), three different masses were measured. Procedure The materials used for this lab are the apparatus shown in Figure 1 that consists of: a Pasco two meter air track, gliders with flags, glider weights, inelastic collision pin and putty receptacle, bumpers, air blowers, two photogates, Pasco 850 Universal Interface, computer, and Pasco Capstone software. These calculations were then used to prove that the total initial momentum is equal to the total final momentum. Percent difference was then calculated (initial momentum final momentum) divided the initial momentum multiplied 100 to get a percent. The equation for total final momentum for this experiment was (where is the first mass times its final velocity, and is the second mass times its final velocity). The total initial momentum is calculated (where is the first mass times its initial velocity, and is the second mass times its initial velocity). In this experiment we calculated the total initial momentum, the total final momentum, and the percent difference. Momentum is calculated multiplying the mass of an object times the velocity of the same object.

PASCO CAPSTONE CALCULATE MOMENTUM FUNCTION HOW TO

Preview text Physics 221 Section 009 Olugbenga Adeyemi Olunloyo Experiment Performed: 10 October 2017 Report Handed In: 17 October 2017 Conservation of Momentum Introduction The scientific purposes of this experiment are to understand the law of conservation of momentum, to learn the definition of momentum and how to analyze it as a vector quantity, to learn the difference between elastic and inelastic collisions, and to verify the law of conservation of momentum for both collisions.

Pasco capstone calculate momentum function